NX 5000

Finally... for the power hungry...the Nexus NX-5000, 500 Watt Power supply. This high wattage 500 Watt power supply is loaded with the latest features to fulfill any of the latest pc systems needs. The NX-5000 power supply is a EPS12V and ATX 2.01 form factor PSU with a slick black and white look.

What can you expect?
• - SLI Ready! (dual PCI-Express)
• - 6 x Molex 4-pin easy connectors
• - 3 x SATA connectors
• - 2 x Floppy conectors

Black and White in every little detail


The NX-5000 is completely black and white. To give you a better idea, let us summarize these details: black outer chassis with only black screws, black fan guard, black mesh sleeves on all cables, black Molex 4-pin easy connectors, black and white combination fan and the NX-5000 even has black internal heat sinks!

Features:
• Real silent power supply, smooth operation with superb cooling
• Real silent large 12 cm black and white fan
• EPS12V and ATX2.01 formfactor
• Excellent air flow
• Longer power cables
• SLI-Ready (2xPCI-E)
• 6 x Molex 4-pin Easy connector
• 3 x SATA connectors
• 2 x Floppy connector
• Output over voltage protection
• Short circuit protection on all output
• Reset Table power shut down
• Approved by: TýV, CSA, UL, NEMKO, FCC, C-tick, BSMI, CE
• 100% burn-in under high ambient temperature (50oC)
• Vacuum-impregnated transformer
• MTBF: 100K hours at 25oC
• 100% Hi-pot tested
• Line input fuse protection
• Longer power cables

• Honey comb grill structure

  Detailed Specifications:

  Over-current protection: The power supply shall be protected from an output over-current event. The supply may shutdown from such an event and require power-on restart.

  • +3.3V : 80 maximum
  • +5.0V : 48 maximum
  • +12V1DC : 20 maximum
  • +12V2DC : 20 maximum
  Short current protection: A short circuit at any output shall cause no damage to the power supply nor blow the primary fuse. The power supply may shut down in the event of a short circuit and require power-on restart. A short circuit consists of application of a test resistance of less then 0.05 ohms at each output with maximum load on all outputs.
  Output risetime: The cold-start enable output voltage risetime of all outputs shall be measured with maximum load on all outputs.
  Risetime (10-95%):
• +3.3V 20mS (max.)
• +5V 20mS (max.)
• +12V1DC 20mS (max.)
• +12V2DC 20mS (max.)
• +5Vsv 20mS (max.)

  Output overshoot: No output voltage shall overshoot or generate spikes at turn-on or turn-off, during momentary power loss, output short, or realistic input voltage or output load changes. Overshoot is defined as any output that exceeds the voltage tolerance plus or minus an additional 5%.

  Efficiency: Overall efficiency must be 70% min. measured at normal AC mains voltage and frequency with maximum loads on all outputs. Power good signal:
  115/230V (full load):
  100-500mS
  Temperature range:
  operating 0oC~50oC
  storage -20oC~+65oC
  Relative Humidity: 90%
  Safety requirements:
  CE, TUV EN60950, NEMKO + CB REPORT, UL 60950, CSA
  
  Dielectric strength:
  Primary to frame ground: 1800 Vac for 1 sec.
  Primary to secondary: 1800 Vac for 1 sec.
  
  

  Insulation resistance:
  Primary to secondary: 20 Meg. ohms min.
  Primary to frame ground: 20 Meg. ohms min.